Here is the step by step process of how to clean out bissell carpet cleaner. Every time you clean your carpet with a carpet cleaner, after that, you need to clean the cleaner itself. If you don’t do that and keep that machine like that, the efficiency will decrease gradually. Next time when you try to clean it, it’ll take more effort to clean as the dirt and soil will be stuck to many parts of the machine.
Sometimes this can lead to damage to the cleaner. Besides, the dirt can develop several harmful germs too. Bissell carpet cleaner is designed to clean soil that includes deeply grounded soil and regular dirt. But it is no exception that you need to keep it clean after every wash. Thus, the machine delivers the best possible service. But if you want to know How to clean out Bissell carpet cleaner, go through this article.
How To Clean Out Bissell Carpet Cleaner
Step 1
After every carpet cleaning, you need to clean the machine’s interior before disassembling it thoroughly. To do that, you have to entirely empty the tanks. Then fill the water tank with normal water. Hot water will be better, though. Then start the machine and run it back and forth. This process will allow the hot water to clean any residue of the cleaning solution from the machine. Along with that, the dirt that is stuck anywhere inside the dirty water collecting path will be cleared too.
Do this for at least 20 minutes. If you can not clean every part of the cleaner every time, you can go with this process. Because in it you don’t have to disassemble any part of the machine. But it will clear almost 100% of the interior of the cleaner. Besides, it’s really easy to apply.
Step 2
After that, you need to clean the house. To do that, take clean water in a bowl or a bucket. Then use the suction of the machine to suck in the water through the hose. It will clear the dirt and soil inside of it. Once done, drain the water. Then you have to lift and stretch the hose to eliminate the remaining water.
Step 3
Although the cleaning of the machine by the step 1 process can save your time and labor. You need to clean all the parts carefully to keep the machine in a healthy state. For that, you should start by cleaning the tank.
First, switch the machine off. Then unplug the power cord. You don’t want to disassemble any part while the cable is plugged. Then remove the water tank from the base. Rotate the lid to open it and empty it in the sink if there is any solution left in it. After that, you need to rinse the tank with hot tap water. Do not leave any corner. Don’t forget to rinse the lid too. Pop-out the filter and wash it with tap water.
The dirty water should be cleaned from the red channel. If your machine has a different tank to collect dirt, you need to clean that too. Dump all the dirt in the sink. Then pour the tank with hot water and clean every corner carefully. After that, rinse it well.
Step 4
Before reattaching the tank, you need to clean the floor nozzle. Remove it from the base and rinse it well. You can use a paperclip for removing the liquid association point. Once you are done cleaning it, you have to wipe and dry it. Finally replace it.
Step 5
But before that, you need to clean the brush roll. You can look for the debris attached to the brush and clean it. But if you want to clean the roll thoroughly, you can remove it from the machine. But for that, you need to go through the manual guide. Most of the devices come with removable brush rolls, and they are not too complicated to remove. You have to unscrew it with a screwdriver.
But make sure not to damage the machine or brushes. Once removed, you can clean all the dirt it attracted. If your brush roll is covered with a cover, you can remove it to clean the whole place properly. Besides the place where the brush roll was set, you can use your bare hands or a small cloth to clean it.
Step 6
You will need the screwdriver again to remove the diverter. Unscrew all the screws and take it out to clean. That will help the machine to keep the suction working properly. Use hot tap water to clean it thoroughly. Then set it back to its place again.
Step 7
Different models come with various attachments. Look for the attachments in your one that will catch dirt. Detach them all one by one. Use hot water to clean them. Then fix them back as they were. But before that, wipe them or leave them aside to dry completely.
Conclusion
No matter how expensive or how advanced your carpet cleaner is, you need to keep them clean to keep them well functioning. And remember, it’s always better to wash it after a carpet cleaning than to keep it for later.
You need to remember that for all the main parts and the attachments you clean, you need to dry them properly before resetting them. Wipe them with dry cloths or keep them in an open-air area for some time. Because if you set them wet and turn the machine on, it can lead to electrocution.